Primary E-Mail
scott@evdeals.com
Alternate E-mail
ghastly1@yahoo.com
snit33a@verizon.net
smacgregor@aasp.net
Call 508-695-3717
Fax 508-643-0233
ELECTRIC
EVdeals Policies
Battery Tests
Dynamometer Tests
FAQs
Tech
Tips
Performance
Testing
Pictures of Custom Projects
Instructions
Yard Sale
© 1999-2011 EVdeals.com
No part of this site may be reproduced or
transmitted in any form or by any means, electronic or mechanical,
including photo- copying, recording, or by any information storage and
retrieval system
without permission in writing from the publisher.
By appointment only!
Scott MacGregor
Plainville, MA 02762
Phone: (508) 695-3717
Fax: (508) 643-0233
***NOTE: The
majority of Lashout/Electrek/Rayos drive
components are
interchangeable with Currie
parts. There are,
however, a few items unique
to
these drives. Please
call me at 508-695-3717
if you need help determining
which to purchase.
| NEW! Replace the stock 1/2" clutch bearing and sprocket with a more rugged 5/8" system. 100% greater torque handling ability for older USPD Currie and all Lashout drives! 70% increase in clutch bearing strength for all newer Currie drives! Eliminates clutch bearing failure common in Currie and Lashout bikes. Includes custom made and hardened steel drive shaft, 5/8" roller bearing clutch, thrust washers, & modified sprocket. Either send me your drive assembly for modification, or do it yourself! Call or write for details. Questions? |
 click to enlarge |
(kit) $99 Special Order Only
|
| NEW: The new Electrec /Lashout/Currie gear housing assembly includes housing, planetary gear, 19 tooth secondary drive sprocket, (#25 chain) oversize 18mm roller bearing clutch, shaft, and ball bearing shaft support. Bolts directly to motor. 4.8:1 reduction to the 19T sprocket. Finally, the answer to blown clutch bearings and worn bronze bushings! |
 |
$185.00 Individual parts available below |
| Here's a layout of the internal parts (excluding the planetary gear unit) in the Rayos/Electrek drive. All parts are available individually. See below. |
18 mm |
|
| Rayos, Electrek hardened steel shaft for roller bearing clutch system. For 18mm bearing. |
18 mm |
$28.00 (shaft) |
| Rayos, Electrek thrust washer set for 18mm bearing drive. |
18 mm |
$12.00 Complete set only |
| Rayos, Electrek 19T sprocket and clutch bearing assembly for 18mm bearing drive. |
18 mm |
$21.00 (sprocket only) $24.00 (clutch bearing only) $43.00 (sprocket with bearing) |
| Rayos, Electrek 19T sprocket, clutch bearing, thrust washers, and shaft. Complete assembly for 18mm bearing drive. |
18 mm |
$79.00 |
| Extra heavy duty steel mounting plate for the 4.8:1 planetary gear housing above. The planetary bolts to this plate, and the motor bolts to the planetary. A great start for your custom built e-bike drive. This is the same mounting plate used on Lashout, Electrec, and Rayos bikes. |
 |
$19.00 |
| Battery pack for Synergy, Lashout, Rayos and Electrec bikes. 24V (same as Currie) 2-12A/Hr batteries. The housing contains a charger port, on/off rocker switch, polarized power connector, carrying handle, quick release mechanism, 40A fuse, and battery status LEDs! Mounting hardware sold separately. |
 |
$174.00 batteries included $89 without batteries Batteries only (2) $85.98 +Shipping
|
Lashout wheel sprocket. Stock sprocket has
54
teeth. Custom sprockets
are available in 48 teeth and 60 teeth. Use these in conjunction with EVdeals
custom pinion sprockets to raise or lower the final drive ratio. Can be used
with Lashout rear wheel or other disk brake hubs. (below)
Stock 54T $29
Custom sprockets (48T-60T) $54-$59 more info?
NOTE:
This rear wheel system does NOT use a skewer
as shown in the above pictures! It's a bolt-on.
Rayos/Electrec/Lashout rear wheel. (26" double wall alloy
rim) Includes
bolt-on wheel,
26" x 1.95" tire, and HD tube. (as shown below)
Cassette
sprocket system.
(cassette not included) Integral 6 bolt disc brake hub matches
custom
(or stock)
drive sprockets shown above.
Complete wheel, tire, and
tube
$129
Cassette for above wheel $29.00
Spacers and 6 sprocket bolts $16.00
|
NEW! LED "fuel gauge" measures your battery voltage to a few 10ths of a volt! Provides an indication of remaining battery power. Mounting posts and brass screws included. Simple 2 wire hookup. Instructions. Available in 24, 36, and 48 volt versions. YOU supply the housing and mounting method. OR You can also get any of the circuits pre-installed in a housing and ready to mount!  Attach to down-tube using double sided tape, plug into charger port, and monitor the battery condition of your bike or scooter to help prevent battery damage! |
|
$19.00 24V ($34 in case) |
 36V, 7 LED 2" x 7/8" x 2" |
$27.00 36V ($42 in case) |
|
|
48V, 7 LED 2" x 7/8" x 2" |
NEW! $29.00 48V ($44 in case) |
|
| NEW
Battery cut-off switch. Large 3/8" brass stud terminals and nuts. Heavy brass feed-thru mounting holes. 2 keys. Rated 100A continuous, 1000A peak@12V, 50A continuous 500A peak @ 24V, 25A continuous 250A peak@48V. |
 |
$10.00 |
| DPST 20A toggle switch. Parallel the 2 halves to create a 40A on/off main power switch. |
 |
$10.00 |
| DPDT rocker switch with two 33" #12 stranded copper wire. Both halves of the switch are in parallel to create a 40A on/off main power switch. |
 |
$20.00 |
| All metal charger port for Currie products and others. |
 |
$9.50 (metal)
|
| All metal XLR type charger cable connector for all Currie (and many other) products. (male) |
 |
$3.50 |
| All metal XLR type charger cable connector for all Currie (and many other) products. (female) |
 |
$12.50 |
| 90 degree all metal XLR type charger cable connector for all Currie (and many other) products. (male) |
 |
$12.50 |
| Switched Lashout brake lever set (2). Both levers have microswitches for controlling various things. The switches are combined so that either one will provide a "closed" condition at the output connector when its lever is pulled. Some have used this for LED brake system lights. |
 |
$39.00 |
| Polarized jumpers for Currie products and other uses. #10 soft, fine stranded wire. Molded polarized connector on each end. |
 |
$7.50 |
| Parallel auxiliary battery harness for adding battery capacity to your Currie (and certain other) scooters or bikes. Add a pair of 10A/Hr batteries in the basket and you've more than doubled your range! Specify scooter or bike harness. (scooter harness includes 6" battery jumper, and 36" battery extension) |
 |
Bike $24.95 Scooter $29.95 |
| Series battery harness for creating 48V battery system. For your Currie and Lashout (and certain other) scooters or bikes. Add a second battery pack on a rear rack and operate a Super BMC 48V motor system. With this harness you can charge your 48V system with a standard 24V charger! Retains all charger, pilot light, output, and on/off switch functions. Specify scooter or bike harness. (scooter harness includes 6" battery jumper, and 36" battery extension) |
 |
$24.95 Scooter $29.95 |
| Thumb Throttle with Cable and Connector (5K) fits all Currie, Lashout, and Electrec products. |
 |
$54.95 |
| Magura Twist Throttle. 63" cable and
pre-installed 3 pin Molex connector.
This is Plug-n-Play for most Currie, Lashout, and Electrec products! (5K)
|
 |
$64.95
(matching left grip $1.90)
|
| 40 Amp blade fuse. Fits all Currie scooters and bikes. |
 |
2.00 |
